MULTI-TECH SYSTEMS, INC. MT5634ZLX/E, MT5634ZLX/E-T/2 Card Type Modem Chip Set Unidentified Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.22, V.22bis, V.32ter, V.32bis, V.34, K56flex, V.90 Fax Modulation Protocol ITU-T V.17, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus PCMCIA 55301 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, P, T, V, W, X, Z &C, &F, &G, &R, &T, &W, &Y, &Z Extended AT Commands \A, \C, \G, \J, \K, \V, \X %A, %G Special Commands "H, -J S Registers S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S18, S25, S30 Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register and the B command. N1 Auto-mode detection enabled. Handshake begins at line speed designated by the S37 register and the B command. Fallback to lower speed if necessary unless in \N1 mode COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode &M4 Hayes autosynchronous mode COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 1200bps or V.21 at 300bps B1 Bell 212A at 1200bps/Bell 103 at 300bps B2 ITU-T V.23 at 75/1200bps originate; 1200/75bps answer B3 ITU-T V.23 at 1200/75bps answer; 75/1200bps originate CONFIGURATION PROFILES & CALL STATISTICS Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles & statistics for last connection Command Function &V0 Displays the active configuration, the two stored user profiles, and the first four phone numbers &V1 Displays statistics for last connection DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode on DTR toggle &D2 Modem goes to command mode and disconnects (hangs up) on DTR toggle; Auto-Answer is disabled on low DTR. &D3 Modem is initialized on DTR toggle DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DSn Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D$ Calling card "Bong" detection enabled D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled JACK TYPE Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Command non-functional; for compatability purposes only Command Function &J0 Send OK to DTE &J1 Send OK to DTE ON-LINE Type: Immediate Format: AT [cmds] On [cmds] Description: Controls on-line command (data transmission) state options. Note: The O command must be placed at the end of the command string. Command Function O0 On-line command mode with no retraining enabled O1 On-line command mode with retraining enabled O3-O14 Force modem to new rate defined by register S62 PULSE DIALING RATIO (INTERNATIONAL VERSION) Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) PULSE DIALING RATIO (JAPAN VERSION) Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 33/67ms at 10pps (Europe) &P1 33/67ms at 20pps RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Dumb answer mode enabled SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting V.32 - AUTO-RETRAIN Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Controls auto-retrain function if poor line quality is detected Command Function &B0 Auto-retrain disabled, modem hangs-up &B1 Auto-retrain enabled if line quality is poor. Hang-up if condition persists longer than threshold set by register S7 &B2 Modem tolerates any line Extended AT Commands COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bi-directional XON/XOFF flow control enabled \Q3 Bi-directional RTS/CTS flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Range: 0-90 Unit: 1 minute Description: Sets the length of time that the modem does not receive information before it disconnects. SPECIAL COMMANDS DIALING MESSAGE CONTROL Type: Configuration Format: AT [cmds] %Mn [cmds] Description: Controls the output of dialing message when dialing a number stored in memory Command Function %M0 Dialing message disabled %M1 Dialing message enabled FIRMWARE VERSION Type: Immidiate Format: AT [cmds] -V [cmds] Description: Displays firmware version number SERIAL PORT BAUD RATE Type: Configuration Format: AT [cmds] $SBn [cmds] Description: Sets the maximum allowable data exchange rate at serial port Command Function $SB300 300bps $SB1200 1200bps $SB2400 2400bps $SB4800 4800bps $SB9600 9600bps $SB19200 19.2Kbps $SB38400 38.4Kbps $SB57600 57.6Kbps $SB115200 115.2Kbps S(STATUS) -REGISTERS BACKSPACE CHARACTER Type: Register Format AT [cmds] S5=n [cmds] Range: 0-127 Unit: ASCII Description: Selects a character used for backspace Note: A value greater than 32 will disable backspace DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Speed of last connection S37=3 300bps S37=5 1200bps S37=6 2400bps S37=7 4800bps S37=8 7200bps S37=9 9600bps S37=10 12.0Kbps S37=11 14.4Kbps S37=12 16.8Kbps S37=13 19.2Kbps S37=14 21.6Kbps S37=15 24.0Kbps S37=16 26.4Kbps S37=17 28.8Kbps S37=18 33.6Kbps DTE RATE STATUS Type: Register Format AT [cmds] S62=n [cmds] Description: Sets the DTE rate status Command Function S62=0 300bps S62=1 600bps S62=2 1200bps S62=3 2400bps S62=4 4800bps S62=5 9600bps S62=6 7200bps S62=7 12.0Kbps S62=8 14.4Kbps S62=9 16.8Kbps S62=10 19.2Kbps S62=11 21.6Kbps S62=12 24.0Kbps S62=13 26.4Kbps S62=14 28.8Kbps S62=15 38.4Kbps S62=16 57.6Kbps S62=17 115.2Kbps DTE TRANSFER SPEED Type: Register Format AT [cmds] S72=n [cmds] Description: Sets the DTE speed during data transfer Command Function S72=0 Last auto-baud S72=1 300bps S72=2 600bps S72=3 1200bps S72=4 2400bps S72=5 4800bps S72=6 9600bps S72=7 7200bps S72=8 12.0Kbps S72=9 14.4Kbps S72=10 16.8Kbps S72=11 19.2Kbps S72=12 21.6Kbps S72=13 24.0Kbps S72=14 26.4Kbps S72=15 28.8Kbps S72=16 38.4Kbps S72=17 57.6Kbps S72=18 115.2Kbps TRANSMISSION LEVEL (JAPAN) Type Register or Configuration Format AT [cmds] S64=n [cmds] Range 9-20 Default 15 Unit -1 dBm Description Sets the signal level for transmission (Japan version) V.90 DOWNSTREAM DATA RATE Type: Register Format AT [cmds] S38=n [cmds] Description: Sets the maximum allowable V.90 downstream rate attempted during handshake process. Command Function S38=0 56K disabled S38=1 56K automatic speed select S38=2 29.3Kbps S38=3 30.6Kbps S38=4 32.0Kbps S38=5 33.3Kbps S38=6 34.6Kbps S38=7 36.0Kbps S38=8 37.3Kbps S38=9 38.6Kbps S38=10 40.0Kbps S38=11 41.3Kbps S38=12 42.6Kbps S38=13 44.0Kbps S38=14 45.3Kbps S38=15 46.6Kbps S38=16 48.0Kbps S38=17 49.3Kbps S38=18 50.6Kbps S38=19 52.0Kbps S38=20 53.3Kbps S38=21 54.6Kbps S38=22 56.0Kbps V.90 MODE SELECTION Type: Register Format: AT [cmds] S109=n [cmds] Description: Selects modem operating mode Command Function S109=0 V.90 disabled S109=1 K56flex or V.90 mode enabled S109=2 V.90 mode enabled; K56flex disabled